SFP+ SR Optical Transceiver

1/10Gbps 850nm Multimode Datacom SFP+ Optical Transceiver

Features

1. Hot-pluggable SFP+ footprint
2. Supports rate selectable 1.25 Gb/sOr 9.95 to 10.3 Gb/s bit rates
3. Power dissipation < 1W
4. RoHS-6 compliant ( lead-free )
5. Single 3.3V power supply
6. Maximum link length of 300m on2000 MHZ-km MMF
7. Uncooled 850nm VCSEL laser
8. Receiver limiting electrical interface
9. Duplex LC Connector
10. Built-in digital diagnostic functions
11. Commercial temperature range： 0°C to 70°C(Standard), -40°C to 85°C (Industrial)

Applications

1. 1000BASE-SX 1G Ethernet
2. 10GBASE-SR/SW 10G Ethernet
3. Other optical links

Product description

F-tone’sFTCS-851X-02X 1G/10G Dual-Rate SFP+ transceivers are designed for use in 1-Gigabit and 10-Gigabit Ethernet links over multimode fiber. They are compliant with SFF-8431, IEEE 802.3-2005 10GBASE-SR/SW and 1000BASE-SX. Digital diagnostics functions are available via a 2-wire serial interface, as specified in SFF-8472. The FTCS-851X-02X is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s recommended settings for interoperability with an SFP+ limiting module. This product is for applications specifically designed for 10G SFP+ ports and 1G/10G SFP+ ports and not native 1G SFP ports. The transceiver is RoHS compliant and lead free per Directive 2002/95/EC5.

Absolute Maximum Ratings

These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions.

Table 3: Absolute Maximum Rating

Recommended Operating Conditions

Notes:

[1] Supply current is shared between VCCTX and VCCRX.

[2] In-rush is defined as current level above steady state current requirements.

Electrical characteristics(T_OP = 0 to 70℃， V_CC = 3.14 to 3.46 Volts)

Notes:

1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.

2. Voltage swing for 1G operation is equivalent to voltage swing in 10G operation (SFF-8431 Rev3.0).

3. Into 100Ω differential termination. Voltage swing for 1G operation is equivalent to voltage swing in 10G operation (SFF-8431 Rev 3.0).

4. 20–80%. Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’sand four 0’s in sequence in the PRBS^9 is an acceptable alternative. SFF-8431 Rev 3.0

5. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board.

Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V.

6. Testing methodology per SFF-8431. Rev 3.0

Optical characteristics for RS0 = LOW (1G Operation)

(T_OP = 0 to 70℃， V_CC = 3.14 to 3.46 Volts)

Notes:

1. Max is equivalent to 10G max spec.

2. This product has not been designed to support 780-nm laser operation.

3. 20%-80%.

4. Per IEEE 802.3-2005. 9dB extinction ratio transmitter.

Optical characteristics for RS0 = HIGH (10G Operation)

(T_OP = 0 to 70℃， V_CC = 3.14 to 3.46 Volts)

Notes:

1. Per Tradeoff Table 52.8, IEEE 802.3-2005

2. Average Power figures are informative only, per IEEE802.3-2005.

3. Measured with worst ER; BER<10^-12; 2³¹ – 1 PRBS.

4. Per IEEE 802.3-2005.

General Specifications

Notes:

1. 1000BASE-SX. Tested with a 2⁷ – 1 PRBS. See Section I, Note 5 for RS0 conditions for 1.25Gb/s operation.

2. 10GBASE-SR/SW. Tested with a 2³¹ – 1 PRBS. See Section I, Note 5 for RS0 conditions for 10.3 Gb/s operation.

Pin Descriptions

       Figure1.Electrical Pin-out Details

Notes:

[1] Module circuit ground is isolated from module chassis ground within the module.

[2].should be pulled up with 4.7k – 10k ohms on host board to a voltage between 3.15Vand 3.6V.

[3]Tx_Disable is an input contact with a 4.7 kΩ to 10 kΩ pullup to VccT inside the module.

[4]Mod_ABS is connected to VeeT or VeeR in the SFP+ module. The host may pull this contact up to Vcc_Host with a resistor in the range 4.7 kΩ to10 kΩ.Mod_ABS is asserted “High” when the SFP+ module is physically absent from a host slot.

[5]RS0 and RS1 are module inputs and are pulled low to VeeT with > 30 kΩ resistors in the module.

Ordering information